Laser marking machine manufacturers analyze the fault handling and causes of the marking machine

Symptom 1: The print needle does not move.

Cause of failure: The compression screws on the X and Y axis drive belts of the printer are loose.

Troubleshooting: Tighten the compression screws on the X and Y axis drive belts of the printer.

Trouble phenomenon 2: The printing is normal, the characters are not beautiful..

Cause of failure: The printing needle is not tightened, the tip of the printing needle is damaged, lack of lubrication or a foreign object is stuck so that the printing needle cannot move.

Troubleshooting: Tighten print pins, replace them if necessary, check rails and belts, clean and lubricate if necessary.

Symptom 3: No indicator light is on after the computer or controller is turned on.

Causes of failure: the power cord is not plugged in properly, the power cord is disconnected, the power cord (or plug) is corroded, the print switch is damaged, and the socket has no electricity.

Troubleshooting: Plug in the power cord and confirm whether the socket has electricity. Note: If you lack relevant knowledge, please do not repair it by yourself. If necessary, consult a professional.

Symptom 4: There is no wind from the power fan after the computer is turned on.

Cause of failure: The regulated power supply of the computer is damaged, and the fan blades of the laser marking machine are stuck by foreign objects.

Troubleshooting: replace the computer's regulated power supply (standard power supply is not expensive, replacement is more convenient and cheaper than repair), and remove foreign objects on the fan blades.

Symptom 5: No display on the computer screen.

Causes of failure: Poor connection of the screen signal cable or damage to the computer display card, damage to the video cable, damage to the computer graphics card, the monitor is not powered on or the switch is not turned on, the monitor contrast and brightness settings improper.

Troubleshooting: plug in the screen signal cable or replace the computer display card, reset the display brightness and contrast, and power on the display.

Symptom 6: The printing process stops suddenly..

Cause of failure: external interference..

Troubleshooting: Press the power switch on the controller panel to restart the controller..

Fault phenomenon 7: The screen display is wrong, the graphics are displayed, and the characters are damaged.

Cause of failure: wrong operation..

Troubleshooting: Press the reset switch of the computer (Reset) to restart the computer.

After selecting the object, right-click the color bar color to modify the color of the outer frame of the object, and left-click the color bar to modify the fill color of the object ( The function is the same as that of CorelDRAW) The first data after the color in the property bar (default 0.010mm) is the step size of the color, the second data (15.0us) is the intermediate delay of the color, and the last parameter is the color of the color. Engraving times, when it is 0, no engraving. Double-click the color bar to switch the engraving times between 0 and 1. The order of the colors represents the order in which the lines of this color are engraved. As shown in the figure above, when engraving each graphic object, Carve in the order of red, yellow, green... black and gray.

How to change the order Select the color to change the order, left-click and hold, and drag it to the desired order, for example, the 'black' line should be in the desired order. The 'yellow' line is engraved before, select 'black

There is a 'pentagon' and a 'text' in the document, the engraving order of 'pentagon' is 1, the engraving order of 'text' is 2, No matter what the color order of IC automatic laser marking machine is when engraving, the engraving machine always engraves 'pentagon' with order 1 first, and then engraves 'text' with order 2. When engraving 'pentagonThe engraver engraves its border and fill lines in color order.

Right-click the color parameter, the following menu will appear Cut: Copy the selected color parameter to the clipboard, Copy: Copy the selected color parameter to the clipboard, Paste: paste the parameters in the clipboard to the selected color parameters, import parameters: import the saved color parameters to the selected color parameters, save parameters: save the selected color parameters to the hard disk for easy recall when necessary, save Set as default value: Save the selected color parameter as the default value, and each color parameter will be set as the default value each time a new document is created.

The method of selecting color parameters ①, directly click the color object to be selected, ②, press the 'Ctrl' key to increase or decrease the selected color object, ③, press The 'Shift' key increases or decreases some selected color objects, which are all objects between the clicked color object and the selected color object.

have manifold cij printer effects, ranging from date coding machine to date printing machine.

We believe our capacity can give you an impressive experience by using cij printer.

Knowing what promotions are popular and get the most activity as cij printer from current and potential customers can play a role in your overall strategy.